HomeNewsCompany news
Maintenance of Waterproof SPC Flooring
Sep 29, 2020

Purpose of cleaning and maintenance of waterproof SPC flooring

1. Improve the appearance: immediately remove the stains often caused in the ordinary use, so that the elastic lock floor fully presents its extraordinary appearance and natural smoothness.

2. Protect the locking floor: prevent the corrosion of unexpected chemicals, cigarette butts, shoe prints, oil and water on the elastic lock floor, reduce the damage of mechanical equipment on the surface to the minimum bottom limit, and make the rubber floor have enough durability to make full use of, thus increasing the service life of the lock floor.

3. Convenient care: because of its inseparable surface structure and unique treatment, pay attention to the usual cleaning and maintenance, which can make the locking floor easy to care and extend the service life.

Precautions for waterproof SPC flooring care

1. All kinds of wastes on the ground should be eliminated immediately.

2. It is absolutely forbidden to soak the lock floor in the open water. Although some floors are decorated with a waterproof sealant to cut off the water source, the long-term invasion of the floor will seriously damage the service life of the locking floor. In the whole cleaning process, the wastewater shall be sucked away immediately by a water suction machine.

3. For the area with a large flow of people and great damage, it is necessary to shorten the maintenance cycle time and increase the number of waxing times of high-strength surface wax.

4. It is absolutely forbidden to use hard and unsmooth cleaning articles (such as steel wire brush, wiping cloth, etc.) to avoid sharp objects impacting the elastic ground.

5. It is highly recommended to place cushions in the passageways of mass venues with high passenger flow, so as to avoid contamination and scratch of building materials such as stains and sand particles.

waterproof spc flooring

Maintenance methods of waterproof SPC flooring at different stages

1. Cleaning and maintenance of locking floor after paving / before application

(1) Remove the dust and dirt on the floor surface of the lock.

(2) Clean and remove the maintenance wax, vegetable grease, dust, and its stains on the surface layer of the lock floor, and absorb the wastewater with a water suction machine.

(3) Wash and suck with cold water.

(4) If necessary, upper 1-2 layers of high strength surface wax.

2. Waterproof SPC flooring cleaning and maintenance

(1) Push dust or dust collector to remove dust.

(2) Wet tow.

3. Waterproof SPC flooring cleaning and maintenance every quarter

(1) Push dust or dust collector to remove dust.

(2) Lock the floor cleaning and polishing agent according to 1:30 water dilution, mop the floor or cooperate with a high-speed polishing machine and bright red grinding plate to carry out grinding.

(3) Upper 1-2 layers of high strength surface wax.

(4) If necessary, be able to cooperate with high-speed grinding and polishing machine and milky white polishing pad for polishing.

4. Complete renovation

(1) Push dust or dust collector to remove dust.

(2) Apply 1:12 dilution of super-strong dewaxing water and evenly spread it on the ground. Wait for 5-12 minutes. Clean and remove wax at a low speed with a floor scraper and a bright red grinding plate. The wastewater shall be immediately sucked away with a suction machine.

(3) Wash with cold water and suck it away until there is no residual detergent left on the floor.

(4) If necessary, upper 1-2 layers of high strength surface wax.

5. Solution to the special stain of waterproof SPC flooring

(1) Oil stains: for some oil stains, pour the source liquid of water-soluble oil remover on the pure cotton towel immediately and wipe them; for large-scale oil stains, clean the water-soluble deoiling agent with 1:12 diluent and clean it at a low speed with a floor scraper and a bright red grinding plate.

(2) Black offset printing: use spray cleaning and maintenance wax to cooperate with high-speed grinding and polishing machine and milky white polishing pad for polishing. For a long time of black offset printing, a super-strong black offset printing remover can be immediately poured on the cotton towel to wipe.

(3) Gum: pour it onto the cotton towel immediately with professional super strength degumming agent and wipe it off.

  • 12 Hengcui Road, Henglin Town, Changzhou, Jiangsu, China
  • 0086-13912343471    
  • jack@gitiafloor.com